Mass Transfer Lab Equipment

Drying Chamber : Insulated double wall chamber. Size 20 x 20 x 25cm Weighing Balance : Digital, 0-1000gm. of ± 1 gm resolution. Hot Air Circulation : By forced draft fan, Arrangement is done to vary the air flow rate. Heating Chamber : Compatible capacity. Heater : Nichrome wire heater. Control panel comprises of : Digital Temp. Indicator : 0-199.9° C (with multi-channel switch) Temperature Sensors : RTD PT – 100 Type Standard make on/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided Along with the Apparatus The whole set-up is well designed and arranged in a good quality painted structure SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 2.5 kW. Wet Solid. Floor area 0.75 m x 2 m.

Size : Customize

Voltage : 220-240 Volt (v)

Material : MS

Application : Industrial

Warranty : 1 Yr.

Supply Ability : As per the order Received Per Month

Extraction Column : Material Borosilicate Glass, Dia 55 mm, Height 750 mm (approx). Packing : Rasching Rings, Material Borosilicate Glass, Feed Tanks : Material Stainless Steel, Cap. 20 Ltrs. (2 Nos.) Extract & Raffinate Tanks : Material Stainless Steel, Cap 10 Ltrs. Feed Circulation : By Compressed Air. Pressure Regulator : 0-2 kg/cm2. Pressure Gauge : Bourdon type, 0-2 kg/cm2. Flow Measurement : Rotameters (One each for solvent & solute) Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus Special arrangement for changing height of interface zone is done. The whole set-up is well designed and arranged in a good quality painted structure. SERVICES REQUIRED Compressed Air Supply at 2 Bar, 0.5 CFM. Water Supply Drain. Required Chemicals & Laboratory Glassware.

Specifications Extraction Column : Material Stainless Steel Dia 150 mm, Height 750 mm (approx) Plates: Material Stainless Steel, with Radial opening. Mixer: Stainless Steel Impellers fitted on Stainless Steel Shaft coupled to a motor & reduction gear box. Screw Conveyor: Material Stainless Steel, Compatible capacity, housed in GI Pipe and driven by a motor & reduction gear box. Solvent Flow Measurement: Rota meter. Solvent Tank: Made of Stainless Steel, Capacity 30 Ltrs. Double wall. Feed circulation: Magnetic Pump made of Polypropylene to Circulate solvent. Maximum working temperature is 60°C. Heater: Nichrome wire heater. Feed Hopper: Suitable capacity. Filtration Sieve: Material Stainless Steel. Receiving Tank for: Material Stainless Steel. Extracted solid waste: Compatible capacity. Temperature Sensor: RTD PT-100 type. Control panel comprising of: Digital Temp. Controller: 0-200°C, For Feed Tank Standard make on/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 3 kW. Solvent : 50 ltrs Solid : 30 kg.

SPECIFICATIONS Distillation Column : Material Stainless Steel, Dia 110mm, seven plates. Pressure Gauge : Bourdon type Rotameter : For cooling water flow rate measurement. Steam Generator : Made of Stainless Steel, provided with Pressure Gauge & Level Indicator, Safety valve & insulated with ceramic wool and Cladding with Aluminum foil. Reflux Divider : Special arrangement to change R/D ratio automatically. Condenser : Shell & Tube type made of Stainless Steel. Bottom product tank : Made of Stainless Steel, capacity 5 Ltrs. Distillate tank : Made of Stainless Steel, capacity 5 Ltrs. Heater : Nichrome wire heater. Temp. Sensors : RTD PT-100 type Control panel comprises of: Digital Temp. Controller : 0-199.9°C, For Reboiler. Digital Temp. Indicator : 0-199.9oC, with multi-channel switch With Standard make on/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided along with the apparatus The whole set-up is well designed and arranged in a good quality painted structure SERVICES REQUIRED Water Supply 2 LPM at 5 m head. Drain. Electricity Supply: 1 Phase, 220 V AC, 6 kW. Required Chemicals Refractometer for analysis.

Specification Distillation Column : Material Stainless Steel , Dia 80mm, Length 900mm (approx). Packing Material : Borosilicate Glass Rasching Rings. Pressure Gauge : Bourdon type Rotameter : For cooling water flow rate measurement. Steam Generator : Made of Stainless Steel, provided with Pressure Gauge & Level Indicator, Safety valve & insulated with ceramic wool and cladding with Aluminium foil. Reflux Divider : Special arrangement to change R/D ratio automatically. Condenser : Shell & Tube type made of Stainless Steel. Distillate tank : Made of Stainless Steel, capacity 5 ltrs Heaters : Made of Stainless Steel, capacity 5 ltrs : Nichrome wire heater. Temp. Sensors : RTD PT-100 type Control panel comprises of : Digital Temp. Controller : 0-199.9°C, (For Re-boiler) Digital Temp. Indicator : 0-199.90C, with multi-channel switch With Standard make on/off switch, Mains Indicator etc Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus SERVICES REQUIRED Water Supply 2 LPM at 5 m head. Electricity Supply: 1 Phase, 220 V AC, 6.5 kW. Required Chemicals. Refractometer for analysis

Column : Borosilicate Glass Dia 55 mm, Length 750 mm (approx.) Packing : Borosilicate Glass Rasching Ring Feed Circulation : By compressed air. Pressure Regulator : 0-2 kg/cm². Pressure Gauge : Bourdon type Feed Tank : Material Stainless Steel, Capacity 20 Ltrs. Flow measurement : Rotameters (One each for feed, air & CO2). Collecting Tank : Material Stainless Steel, Capacity 10 Ltrs. Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus The whole set-up is well designed and arranged in a good quality painted structure. SERVICES REQUIRED Compressed Air Supply at 2 Bar, 4 CFM. Water Supply Floor Drain. CO2 cylinder with control valve, pressure regulator and Pressure gauges Required Chemicals & Laboratory Glassware

Tube : Material Borosilicate Glass. Water Bath : Material Stainless Steel with two sides made of glass Capacity 8 Ltrs, Fitted with heater and stirrer. Heater : Nichrome Wire Heater. Stirrer : Stainless Steel, Impeller and shaft coupled with FHP motor. Air Circulation : Air Pump. Traveling Microscope : 0-150 x 0.1 mm resolution. Temp. Sensor : RTD PT-100 type Control panel comprising of: Digital Temp. Controller cum-Indicator (For Water Bath 0-199.9°C and Standard make On/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus The whole set-up is mounted on a powder coated base plate. SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 0.6 kW. Required Chemicals & Laboratory Glassware. Table for setup support

SPECIFICATIONS Drying Chamber Material : Stainless Steel Size : 30 x 30 x 30 cm insulated by Ceramic wool and housed in a MS Chamber. Maximum Temperature : 120°C. Heater : Nichrome wire heater Weighing Balance : Digital, 0-1000gm. of ± 1 gm resolution. Temp. Sensor : RTD PT-100 type Control panel comprises of: Digital Temp. Controller 0-199.9°C For Drying Chamber and with Standard make on/off switch, Mains Indicator etc. SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 2 kW. Drying Solids. Table for setup support

Column : Material Borosilicate Glass Dia. 80 mm. Total Length 500mm. Cyclone Separator : Material Stainless Steel, Compatible Capacity with collector. Air Circulation : By forced draft fan, Arrangement is done to vary the air flow rate. Heating Chamber : Compatible capacity Heater : Nichrome wire heater Temperature Sensors : RTD PT-100 type. Control panel comprises of : Digital Temp. Controller : 0 199.9°C (For Hot Air) Standard make on/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus The whole set-up is well designed and arranged in a good quality painted structure. SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 3 kW. Granular and free flowing solid of size 1 to 2 mm.

Distillation still : 1 Ltrs. Capacity, made of Stainless Steel. Insulated by ceramic wool. Condenser : Concentric Tube type. Heater : Nichrome wire Cooling Water Tank : Material Stainless Steel , Capacity 15 Ltrs. Approx. Cold Water circulation : Using FHP Pump. Temperature Sensors : RTD PT-100 type Control panel comprising of Digital Voltmeter: 0-300 Volt. Dimmerstat : 0-230 V, 2A. Digital Temp. indicator: 0-199.90C RTD PT-100 Type with multi-channel switch With standard make on/off switch, Mains Indicator etc. Instruction Manual : An ENGLISH instruction manual will be provided along with the Apparatus The whole set-up is mounted on a powder coated base plate. SERVICES REQUIRED Water Supply. Drain. Electricity Supply : 1 Phase, 220 V AC, 1.5 kW. Refractrometer for Analysis. Required Chemicals

Column (3 Nos.) : Material Borosilicate glass of different dia. Feed tank : Material Stainless Steel, Capacity 20 litres. Receiving tank : Material Stainless Steel, Capacity 20 litres. Feed circulation : FHP, Magnetic Pump made of Polypropylene. Piping : Stainless Steel and PVC of size ¼ . Flow measurement : Rotameter for feed. Stop Watch : Electronic. Instruction Manual : An ENGLISH instruction manual will be provided along wi th the Apparatus The whole set-up is well designed and arranged in a good quality painted structure. SERVICES REQUIRED Electricity Supply : 1 Phase, 220 V AC, 0.5 kW Bench Area : 1.2m x 1m. Required Chemicals & Laboratory Glassware. Colourimeter. Required analyzing equipments as per the system to study