Call : +918068210873
Home » Products » Concrete Lab Equipment

Concrete Lab Equipment

Hydraulic Jack Assembly
close
Hydraulic Jack Assembly
STC-29
FLEXIBLE PIPES: High Pressure hoses for the hydraulic jacks can be supplied at extra cost. These pipes are available in 1 meter length with end connections. Set of platens for self aligning action.
Price : 6000 INR
TENSILE STRENGTH TESTER ( ELECTRICALLY OPERATED )
close
TENSILE STRENGTH TESTER ( ELECTRICALLY OPERATED )
STC-39
SPECIFICATIONS: • The instrument employs a friction- free, accurate, double lever system, the load being applied by means of sliding weight on the top lever. • The capacity of the unit is 900 kgs. After fixing the briquette in the jaws, the machine is switched on. • The sliding weight slides over the calibrated lever thus applying tension to the specimen. • A micro-switch fitted instantly stops the machine on failure of the briquette and on failure the tensile load is accurately read to 0.5 kg. by means of a marker provided on the sliding weight. • The machine can be made opratable for subsequent test only after the sliding weight to its zero position. • Suitable for operation on 230 volts, 50 cycles, single phase, A.C. supply. • Complete with one brass briquette mould and one base plate.
Price : 75000 INR
POZZOLANA CEMENT MORTAR  PERMEABILITY APPARATUS
close
POZZOLANA CEMENT MORTAR PERMEABILITY APPARATUS
STC-38
SPECIFICATIONS: The mortar permeability apparatus comprises three brass/gun-metal cells mounted on a stand and a pressure chamber with a pressure regulator. The cell can accommodate 100 mm dia X 50 mm high specimen. Each cell assembly consists of one base plate. The base plate has one outlet for water and is recessed to hold the specimen in place with a ring washer in between. The top plate has an inlet for water and a suitable connector for the application of pressurized water in the cell. The mould and collar are clamped between the base plate and the top plate with the help of four tension rods and nuts. The cells are mounted on a stand. The pressure chamber is fitted with a pressure regulator which helps in regulating the pressure from 0-7kg/sq.cm.
Price : 35000 INR
CONCRETE PERMEABILITY APPARATUS
close
CONCRETE PERMEABILITY APPARATUS
STC-37
SPECIFICATIONS: • Compressor with pressure gauge 0-20 kg/cm sq. with automatic pressure valve and pressure rubber hose. • Suitable for 440 volts A.C. three phase. • Specimen casting mould C.I. for 100 mm dia X 100 mm high cylinders. • Specimen casting mould C.I. for 150 mm dia X 150 mm high cylinders. • Specimen casting mould C.I. for 150 mm cubes. • Blow stove ½ litre capacity. Resin, Bees wax, Wire brush, Chissel, spare glass cylinder 500 cc capacity.
Price : 25000 INR
Shrinkage Bar Mould Three Gang
close
Shrinkage Bar Mould Three Gang
STC-18
SPECIFICATIONS: The mould, which has 25mm x 25mmx 250mm. effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base It has three compartments.
Price : 11000 INR
Shrinkage Bar Mould (two Gang)
close
Shrinkage Bar Mould (two Gang)
STC-17
SPECIFICATIONS: The mould, which has 25mm x 25mmx 250mm. effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base It has compartments assembled on a angle base plate.
Price : 10000 INR
Mortar Mixer
close
Mortar Mixer
STC-15
SPECIFICATIONS: The apparatus consists of an epicyclic type stainless steel paddle imparting both planetary and revolving motion, by means of gears. It has two speeds of 140+5 r.p.m and 285+10 r.p.m with planetary motions of approximately 62 r.p.m and 125 r.p.m.+ 10 r.p.m. respectively. The stand of the mixer has arrangement to raise for lower the bowl. Complete with stainless steel bowl of about six liters capacity. Suitable for operation on 230 volts,50 cycles, single phase, A.C. Supply.
Price : 50000 INR
LABORATORY CONCRETE MIXER (MOTORIZED)
close
LABORATORY CONCRETE MIXER (MOTORIZED)
STC-14
Concrete mixer Laboratory type, electrically operated. Designed to remove the burden some work of hand mixing. Uniform thoroughly mixed batches can be produced. The counter balanced drum is easy to tilt 1.1/2 to 2cu.ft.mix. The total drum volume is however 3cu.ft. Mounted on a sturdy rubber tyred stand, and the drum is mounted for end discharge and equipped with end towing pole. Equipped with 1/2h.p. electric motor. Suitable for operation on 220/230 volts A.C. Single phase.
Price : 40000 INR
Slump Test Apparatus
close
Slump Test Apparatus
STC-08
Specifications: The Apparatus consists of one slump cone with handles and foot pieces. The Slump cone has internal dimensions 20cm. dia. At base 10cm. top dia. And 30cm. height. Foot pieces can be fixed to the clamps on the base plate .The base plate has lifting handle for easy transportation. One graduated steel rod 16mm dia. x 600mm long, rounded at one end and graduated in mm, is also supplied.
Price : 15000 INR
LE CHATELIER MOULD
close
LE CHATELIER MOULD
STC-04
ACCESSORIES: Mild steel base plate 5inches x 5inches. Fulcrum mould, brass, 70mm 1.0 base die x 60mm I.D. top dia, 40mm height.
Price : 3000 INR
HYDRAULIC JACK (HAND OPERATED)
close
HYDRAULIC JACK (HAND OPERATED)
STC-25
MODEL Capacity in KN Approx. lift in MM Piston Dia in MM Pressure Gauge Dia Min. Div. on Pressure Gauge in KN
Price : 8000 INR
VIBRATING TABLE
close
VIBRATING TABLE
STC-23
SPECIFICATIONS: The apparatus consists of:- • A motor fitted with a variable pitch pulley housed in a cabinet. • The vibrations are imparted by means of off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top. • The table top is 50cm x 50cm. and has stops along its edges to prevent moulds from walking off the table during vibration. • A cross arm adjustable on a vertical rod at the center of the table is provided to hold the moulds while operating the table. • The variable pitch pulley arrangement permits the frequency to be varied sleeplessly between a maximum of 3600 vibrations down to 2600 vibrations per minute. • A speed regulation handle is provided for increasing or decreasing the frequency. • A switch is provided for starting the motor suitable for operation on 1440 volts, 3 phase, 50 cycles, A.C. supply.
Price : 35000 INR
FLEXURE TESTING MACHINE (MOTORIZED) RILEM- CEMBUREAU TEST
close
FLEXURE TESTING MACHINE (MOTORIZED) RILEM- CEMBUREAU TEST
STC-22
SPECIFICATIONS: • It is a motorized, mechanical unit. • The speed is adjusted so that the load increase on the specimen is between 4 to 6kg/sec. • A flexure test attachment for keeping the specimen in position is also supplied. • This consists of two rollers 10mm. diameter and spaced 100mm apart, and a third roller of the same diameter equidistant from 10mm. diameter and spaced 100mmapart, and a third roller of the same diameter equidistant from the first two and for transmitting the applied load to the opposite face of the prism. • The unit is for operation on 230 Volts, single phase, 50 cycles A.C. Supply. Loads are measured on a proving ring fitted with a sensitive dial gauge. • Supplied without proving Ring.
Price : 15000 INR
LENGTH COMPARATOR
close
LENGTH COMPARATOR
STC-12
SPECIFICATIONS: The instrument consists of a channeled base over which two vertical pillars are fixed. An adjustable cross plate is at the top. A dial gauge, reading to.002mm x 12 mm. can be fixed to the top cross plate. The plunger end of the dial gauge can be located upon a 6.5mm. dia. ball or other reference cemented in the specimen. On the base there is a similar recessed seating in which can be placed a second ball or reference point in the specimen. Complete with a stainless steel standardization bar with insulated grip and with 6.5mm dia. balls mounted in the ends. The unit can be supplied with a .0001inch x 1/2inch dial gauge at extra cost if indicated at the time of placing the order.
Price : 6000 INR
FLOW TABLE
close
FLOW TABLE
STC-11
As Per IS: 6932 (Part VIII) This is used for determining the work ability of building limes. Specifications: The Flow table consists of a 30cm. dia. ground and polished steel plate with three inscribed annular circles.7, 11 and 19cm. dia. The table top is arranged for a free fall of 12.5mm by a cam action. Supplied complete with one bras conical mould, 65mm I.D. at base and 40mm I.D. at top, height of the mould 90mm.
Price : 12000 INR
GILLMORE NEEDLE APPARATUS
close
GILLMORE NEEDLE APPARATUS
STC-05
This instrument is used for determining the time setting of hydraulic cement. Specification: A base with a vertical shaft and two horizontal arms. The lower arm is adjustable for height. 1 No.. Initial Needle 1/12 inch dia 1/4 lb.wt. 1No.. Final Needle 1/12 inch dia. 1lb.wt. 1 No. Glass base plate. Complete as above.
Price : 25000 INR
CEMENT SAMPLER
close
CEMENT SAMPLER
STC-01
This is a brass tube approximately 53cm long and 2.8 cm I.D. with a wooden handle. Total length approximately 73cm. The tube has the sharp angular edge which conveniently pierces cement bags. An air hole of approximately 3mm die is drilled on the tube near handle. Total sample collected at one time is 300cm 3 approximately.
Price : 2000 INR
BLAINE'S AIR PERMEABILITY APPARATUS
close
BLAINE'S AIR PERMEABILITY APPARATUS
STC-02
The apparatus is used for determining the fineness of cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement.
Price : 30000 INR
ROLL CRUSHER (LARGE)
close
ROLL CRUSHER (LARGE)
STC-35
• This comprises of two hardened alloy steel rollers with 150 mm, faces and 250 mm. diameters.
Price : 25000 INR
PULVERISER
close
PULVERISER
STC-34
SPECIFICATIONS: It is a self contained grinder, with a rotary disc, having a planetary movement in a vertical plane. This feature gives added life to the moving parts and produces a sample of uniform fineness. Grinding is done between two discs-one stationery and the other revolving eccentrically at high speed. The discs are made from heat treated machinate metal. With the help of a convenient hand wheel, the size of the final product can be adjusted. This can be done, even while the machine is in operation. A self locking device holds the hinged grinding chamber in place and affords easy and quick access to it, for removal of ground samples and for cleaning. The Pulverize has a capacity of reducing about half of a kilogram of a quartz type sample to 100 mesh in a about a minute. The Pulverser is supplied complete with a 3 H.P motor, a starter, a “V” belt pulley drive and mounting wired for 440V, 3 Ph, 50Hz LABORATORY PULVERSER: Disc Diameter - 175mm. Maximum Feed size - 6mm. Yield - 250gms./min. Size of Finished Product -100mesh.
Price : 15000 INR
NEEDLE VIBRATOR
close
NEEDLE VIBRATOR
STC-33
SPECIFICATIONS: • Needle Vibrator with a 25mm. diameter x 350mm, long needle, a one meter long flexible shaft and a motor drive with a swivel head and on/off switch. • Wired fro 230V. Sph. 50Hz.
Price : 4000 INR
Tile Abrasion Testing Machine
close
Tile Abrasion Testing Machine
STC-32
SPECIFICATIONS: The machine consists of:- 1. A disc rotating at a speed of 30 rpm in a circular tray. 2. A bracket is provided to hold the specimen. 3. A counter balance lever loads the specimen. 4. Load applied is 30kgf. 5. A funnel is fitted to evenly spread abrasive powder on the grinding path. 6. A pre-set counter automatically stops the machine after 22 revolutions. 7. This counter is re-adjustable. 8. The machine works on 440 volts AC, three phase electrical supply. 9. On request machine to operate on 230Volts A.C. supply can also be supplied.
Price : 25000 INR
Tile Flexure Testing Machine
close
Tile Flexure Testing Machine
STC-31
SPECIFICATIONS: The machine consists of :- A stand on which two 40mm dia. bearing rollers or 12mm dia. rollers are placed at centre distance of 150mm, 200mm, 250mm, or 2720mm as the case may be. The third upper roller applies centrally flexural load by means of lever arrangement. Lead shot contained in an upper vessel start flowing into lower container at a rate of 45 to 55 kg per minute of 200kg per minute there by, starting loading the specimen. Arrangement is made such that loading automatically stops when specimen breaks. Supplied without lead shots.
Price : 7000 INR
Pumping Units
close
Pumping Units
STC-28
SPECIFICATIONS: The special features of pumping units is that the plungers of the pump have tolerances and no seals are used in the units and special type of non return valves as against traditional ball valves are used, which gives much longer trouble free service. Electrical Pumping Units work on 230Volts A.C. or 440 volts A.C.3 phase depending upon their capacity and these can be operated by hand in case of power failure. The front panel accommodate pressure gauge, on/off switch, slow fast lever to control the rate of loading and indicator lamps. Further in electrical units a micro switch fitted in the pressure gauge and a connected to a relay automatically cuts of the power supply to the unit when gauge capacity is reached. A dummy pointer to record maximum load applied is fitted on the cover glass. In hand operated pumping units, two plungers of different diameter are used. The plunger with larger diameter pumps oil at faster rage and is used for initial loading. Further load is easily applied by the second pump which has a smaller diameter plunger, The lever for operation of the pump is sufficiently long to minimize efforts and these units are suitable for site use.
Price : 35000 INR
Hydraulic Jack Central Hole Type
close
Hydraulic Jack Central Hole Type
STC-27
SPECIFICATIONS: The hydraulic jack has a 25 mm diameter hole going through the center. It is designed for dual direction and had a working stroke of approximately 22cm. A specially designed hand operated pumping unit is supplied for operation in both directions. A detachable handle is provided for operating the pump. • The load is indicated on a 15cm dial hydraulic pressure gauge calibrated 0-50000 x 500kg.
Price : 15000 INR
Sand Absorption Cone And Tamper
close
Sand Absorption Cone And Tamper
STC-20
SPECIFICATIONS: The Equipments comprises of a conical metal mould 1.5inch dia. at the top, 3.5 inch dia. at the base and 2.7/8 inch in height. A metal tamping rod weighing 12 ounces and having a flat circular tamping face 1 inch in diameter.
Unit of Price : Unit/Units
Price : 5000 INR
Shrinkage Bar Mould (FOUR Gang)
close
Shrinkage Bar Mould (FOUR Gang)
STC-19
SPECIFICATIONS: The mould, which has 25mm x 25mmx 250mm. effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base. It has four compartments.
Price : 8000 INR
Laboratory Concrete Mixer
close
Laboratory Concrete Mixer
33
Size : Customize
Voltage : 220-240 Volt (v)
Material : MS
Application : Industrial & Laboratory
Warranty : 1 Yr.
Supply Ability : As per the order Received Per Month
Price : 30000 INR
VICAT NEEDLE APPARATUS WITH DASHPOT
close
VICAT NEEDLE APPARATUS WITH DASHPOT
STC-03
SPECIFICATION: The apparatus consists of a metallic frame bearing a freely movable rod with a cap at top, one vicat mould, split type and glass base plate and one set of needles one each initial needle, final needle and consistency plunger.
Price : 15000 INR
KELLEY BALL PENETRATION APPARATUS
close
KELLEY BALL PENETRATION APPARATUS
STC-06
Specifications: • It consists of a cylinder with a ball-shaped bottom and handle together weighing 15 kg. • A strip frame, guides the handle and serves as a reference for measuring the depth of penetration. • The handle is graduated in MM. • Penetration can be recorded to the nearest 0.5mm.
Price : 25000 INR
VE BEE CONSISTOMETER
close
VE BEE CONSISTOMETER
STC-07
Specifications: the equipment consists of: A vibration Table size 380mm long and 260mm wide, resting upon elastic support at a height of about 305mm above the floor, complete with start/stop Switch, Cord and Plug. A holder is fixed to the base into which a swivel arm is telescoped with funnel and guide sleeve. The swivel arm is also detachable from the vibrating Table. A graduated rod is fixed on a swivel arm and at its end a plastic disc is screwed. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating Table. A slump cone open at both ends with lifting handles and a Tamping rod of size 16mm dia and 600 mm long, rounded at one end.
Price : 20000 INR
AIR ENTRAINMENT METER
close
AIR ENTRAINMENT METER
STC-09
Product Type : Study
Color : Yello-blue
Material : S.S.
Operate Method : Manually
Usage : Lab experiment
Supply Ability : 10 Per Month
Price : 25000 INR
COMPACTION FACTOR APPARATUS
close
COMPACTION FACTOR APPARATUS
STC-10
VOLUME CHANGE APPARATUS
close
VOLUME CHANGE APPARATUS
STC-13
SPECIFICATIONS: 1. The apparatus comprises of one mould 100mm x 100mm x 250mm, 2. effective gauge length complete with base plate, 3. Four reference pins, 4. One length comparator frame, 5. One stainless steel reference bar with insulated grip, 6. one dial gauge, 0.02mm x 10mm.
Price : 10000 INR
SHRINKAGE BAR MOULD
close
SHRINKAGE BAR MOULD
STC-16
SPECIFICATIONS: It consists of:- • The mould, which has 25mm x 25mmx 250mm. • effective gauge length is made of mild steel and has accurately machined faces. • The parts of the moulds are tight fitting and firmly held together when assembled. • Supplied complete with base
Price : 10000 INR
JOLTING APPARATUS
close
JOLTING APPARATUS
STC-21
Specifications: The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800mm from the center of the table. There is a projecting lug with a plane face on the ower face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gear box through a V-belt and pulleys. The cam rotates at a rate of 60 rev./min. A stroke counter fitted with micro-switch is provided which stop the machine after 60 jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, single phase, A.C. supply. Spares and Accessories: (1) Steel mould with base plate having three compartments each having (2) Apparatus for demoulding the specimen.
Price : 35000 INR
VIBRATING MACHINE
close
VIBRATING MACHINE
STC-24
SPECIFICATIONS: The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The center of gravity of the assembly is brought to the center of the eccentric shaft or within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould. The frequency of vibration is 12000+/-400 vibration per minute. Supplied complete with on 7.06cm cube mould with loose base plate a time switch 0- 5minsx1min and certificate of vibration from a standard Laboratory.
Price : 40000 INR
Integral Type Hydraulic Jacks Capacity
close
Integral Type Hydraulic Jacks Capacity
STC-26
DESCRIPTION: These are hydraulic jacks with integral pumping unit. The hydraulic pressure gauge is of 15cm dial on the side of hydraulic jack. A detachable lever is provided to operate the pump. Lift of the ram is 95 to 100mm. Face of the ram is flat. NOTE: Hydraulic jacks of 1000Kn & 5000KN capacity can be supplied with two speed pumping units. These jacks have lift of approximately 200mm.
Price : 15000 INR
THICKNESS GAUGE
close
THICKNESS GAUGE
STC-30
SPECIFICATIONS: The machine consists of a stand on which two 40mm dia. bearing rollers or 12mm dia. rollers are placed at centre distance of 150mm, 200mm, 250mm, or 2720mm as the case may be. The third upper roller applies centrally flexural load by means of lever arrangement. Lead shot contained in an upper vessel start flowing into lower container at a rate of 45 to 55 kg per minute of 200kg per minute there by, starting loading the specimen. Arrangement is made such that loading automatically stops when specimen breaks. Supplied without lead shots.
Price : 5000 INR
ROLL CRUSHER (SMALL)
close
ROLL CRUSHER (SMALL)
STC-36
The drive is by a heavy motor, through V belts, to a set of gears and further to the rollers.
Price : 25000 INR
TENSILE STRENGTH TESTER
close
TENSILE STRENGTH TESTER
STC-40
SPARES AND ACCESSORIES: Brass briquette mould for making cement briquette for tensile strength on cement, without base plate. Base plate machined flat to + 0.005 inch. Brass briquette mould three gang complete with base plate
Price : 55000 INR


Back to top
SUPERB TECHNOLOGIES All Rights Reserved.(Terms of Use)
Developed and Managed by Infocom Network Ltd.