Call : 918037402041

Aggregate Testing Lab Equipment

Product Image (STC-32)

TILE ABRASION TESTING MACHINE

Price: 25000 INR

SPECIFICATIONS: The machine consists of:- 1. A disc rotating at a speed of 30 rpm in a circular tray. 2. A bracket is provided to hold the specimen. 3. A counter balance lever loads the specimen. 4. Load applied is 30kgf. 5. A funnel is fitted to evenly spread abrasive powder on the grinding path. 6. A pre-set counter automatically stops the machine after 22 revolutions. 7. This counter is re-adjustable. 8. The machine works on 440 volts AC, three phase electrical supply. 9. On request machine to operate on 230Volts A.C. supply can also be supplied.

Product Image (STA-02)

LENGTH GAUGE

Price: 3000 INR

SPECIFICATIONS: It consists of a hard wood base with vertically mounted metal.

Product Image (STA-03)

CYLINDRICAL MEASURES

Price: 3000 INR

SPECIFICATIONS: Calibrated cylindrical measures of sheet iron with handles. Consists of 3 measures one each 3 liters capacity, 15 liters capacity and 30 liters capacity. One tamping rod, round, 16mm dia. and 600mm long, one end rounded.

Product Image (STA-04)

METAL MEASURES

SPECIFICATIONS: Made from sheet iron, complete with handle, capacity 10litres or 20litres.

Product Image (STA-05)

DENSITY BASKET

Price: 3000 INR

SPECIFICATIONS: Made of brass with stainless steel wire mesh 6.3mm size ruggedly constructed. Approximately 20cm dia. x 20cm. high. Complete with handle.

Product Image (STA-06)

RIFFLE SAMPLE DIVIDER

Price: 5000 INR

SPECIFICATIONS: It consists of a sheet metal box mounted on legs and fitted with a series of chutes of equal width which discharge the material alternatively in opposite directions into separate pans. The chutes of the riffle are steep enough to allow rapid flowing of the material:- The instrument has 14 Nos. chutes of 13mm width and is complete with two receivers.

Product Image (STA-07)

AGGREGATE CRUSHING VALUE APPARATUS

Price: 2000 INR

SPECIFICATIONS: Consists of M.S. Cylindrical container 150mm + 0.5mm dia. x 130mm to 140mm high with base plate 200 to 230 mm/sqr x 6mm thick. A plunger of 148mm + 0.55mm dia. x 100 to 115mm high. tramping rod, 16mm dia x 600mm long, one end rounded. 1 No. metal measure 115 + 0.55mm dia. x 180 0.5mm high.

Product Image (STA-08)

AGGREGATE IMPACT TESTER

Price: 25000 INR

SPECIFICATIONS: The instrument consists of a circular base with two vertical guides. The hammer of weight 13.75 + 0.25kg can be raised to fall freely down the vertical guides. The height of fall can be adjusted through 380+ 5mm. The hammer is provided with a locking arrangement. The hammer falls freely to the base and is removable for emptying. Supplied complete with metal measures 75mm dia. x 50mm high (for specimen preparation) and tamping rod 230mm long x 10mm dia.

Product Image (STA-09)

SPECIFIC GRAVITY AND WATER ABSORPTION OF AGGREGATE

Price: 25000 INR

SPECIFICATIONS: The outfit comprises of- 1No. Semi-self indicating balance, capacity 5 kg, accuracy 0.5gm, provision is made in this balance to suspend density basket under material pan. Balance is supplied with necessary set of weights. This balance is mounted on an angle iron frame stand. 1 No. Density Basket. 1 No. Air tight container of capacity similar to that of density basket 1 No. Water tight container to suspend density basket. 1 No. G.I. Tray of area not less that 650cm sq. 2 Nos. Absorbent clothes 75cm x 45cm.

Product Image (STA-10)

DEVAL ATTRITION TESTER

Price: 25000 INR

SPECIFICATIONS: It consists of two hollow cylinders closed at one end and provided with tight fitting covers at the either end. These cylinders are mounted on a shaft at an angle of 30 degree with the axis of rotation of the shaft. The shaft rotates at 30-33 rpm through a reduction gear operated by a motor and is provided with a revolution counter. Complete with abrasive charges consisting of 12 Nos. Hardened steel balls of 48mm. dia. Suitable for operation on 440Volts, 3 Phase, 50 cycles. A.C. Supply.

Product Image (STA-11)

DORRY ABRASION TESTING MACHINE

Price: 35000 INR

SPECIFICATIONS: It consists of a disc rotating about a shaft connected to a reeducation gear box occupied to a motor. The disc rotates at 20-30 rpm. Under the rotating disc is a tray with an outlet to facilitate the removal of sand. Two conical hoppers are mounted on a bracket fixed to the circular tray. An arrangement is made for start and stop the flow of sand. Two holes are provided for mounting two specimens simultaneously. Two containers with weights are supplied to keep the specimens pressed against the rotating disc. Suitable for operation on 220Volts, 50 cycles, A.C. supply.

Product Image (STA-12)

PULL MILL FOR GRINDING LIME MORTAR

Price: 35000 INR

SPECIFICATIONS: It is of weided steel construction, having an in internal diameter of 12 inch x 13.5 inch long (volume 1 cu.ft.) and is made of 5/16 inch thick steel plate. The drum is supported on heavy duty ball bearings on the two ends. It has an opening of 4 inch width along the full length of drum. An air and water tight cover is provided to close the opening after the specimen has been put inside the drum. The speed of rotation is 28- 30rpm. The pug mill has an arrangement for being held in any position. A revolution counter for recording the revolutions of the mill is fixed on the machine. Twelve ¾ inch dia. steel balls are also supplied with the unit. It is fitted with a ½ H.P. electric motor to operate on single phase, 220/230 volts A.C. supply.

Product Image (STA-13)

LOS ANGLES ABRASION TESTING MACHINE

Price: 35000 INR

SPECIFICATIONS: The machine consists of a hollow cylinder mounted horizontally on a study frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-33 rpm. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with abrasive charges consisting of a set of twelve hardened steel balls, approximately 48mm dia. Suitable for operation on 440volts, 3 phase, 50 cycles, A.C. supply.

Product Image (STA-01)

THICKNESS GAUGE

Price: 5000 INR

SPECIFICATIONS: It Consists of a frame with a sliding panel. The panel slots of different standard length and widths accurately cut.

Product Image (35)

Los Angles Abrasion Testing Machine

Price: 50000 INR
  • Delivery Time:As per Order Quantity Days
  • Supply Ability:As per the order Received Per Month
  • Warranty:1 Yr.
  • Size:Customize
  • Application:Industrial
  • Voltage:220-240 Volt (v)
  • Material:MS
X


Back to top
SUPERB TECHNOLOGIES All Rights Reserved.(Terms of Use)
Developed and Managed by Infocom Network Ltd.